Miniart
Miniart 1:35 Czech City Building
Sold Out
Miniart 1:35 - Czech City Building - Plastic model kit #35018
The kit contains 247 parts.
Includes Soviet wall slogans and signs 1944-45.
Model Dimension: Length 166mm, Height 316mm, Width 118mm
Box: 345mm x 240mm x 70mm
Miniart 1:35 Daimler Dingo Mk III w/Crew
Sold Out
Miniart 1:35 - Daimler Dingo British Scout Car Mk III w/Crew - Plastic Model Kit #35077
The Dingo was a British light two-man armoured car, relatively low and wide enough to have the required stability for fast off-road rides. Its initial armour was thin, just enough to stand against infantry ordnance. At the Army’s request, it was thickened, reaching 30mm (1.18 in) on the front nose and glacis. Deflecting armoured sloped panels were welded all around the central framework. The front driving compartment had four opening hatches. The engine was the regular Daimler 6-cyl 2.5 l 55 hp (41 kW), fed by a 300 l (79.25 gal) gasoline reserve (two tanks), which gave an incredible long range for its small size. The transmission consisted of a pre-selector gearbox, fluid flywheel, five forward gears and five reverse gears, allowing steering with all four wheels. This feature gave the Dingo a very tight turning radius, only 7m (23 ft), but the system was tricky to master for inexperienced drivers, so a more conventional design with front-wheel steering was chosen for the Mk.II.
During the course of wartime production, it appeared that the flat bottom plate, which allowed the crossing of uneven ground, was highly vulnerable to mines. The rubber tires were of the run-flat semi-solid type, so no spares were carried, but their toughness was compensated by the massive vertical coil springs, to give a smooth ride. There was a swiveling seat next to the driver, for a machine-gun servant/radio operator, equipped with a N°19 wireless radio set. The base armament was a removable cal. 0.303 (7.7 mm) Bren gun, with a dozen spare magazines. This armament could be swapped over for a heavier Boys antitank rifle (cal 0.55 in/14 mm). This gave the vehicle, which was fast and well-protected, with a good engine and low profile, a real advantage against all sorts of light vehicles, making it perfectly suited for reconnaissance and liaison missions.
The Dingo was produced from 1939 to 1945, and remained virtually unaltered.
The Mark I had a flexible sliding roof and the all-wheel steering. It was difficult to handle for inexperienced drivers.
The Mark IA was a sub-variant equipped with a folding roof.
The Mark IB had a reverse cooling air flow and new armored grilles for the radiator, allowing better ventilation. The bulk of these vehicles served in the Libyan desert.
The Mark II had a revised steering system, using only the front wheels. The lighting equipment was modernised, altogether with the Mark IB modification range.
The Mark III was the final version, coming in 1944 with a waterproof ignition system and no roof at all.
The kit contains 262 parts.
Includes parts for one armoured car and three figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Dingo MK IB British Armoured Car w/Crew
Sold Out
Miniart 1:35 - Dingo MK IB British Armoured Car w/Crew - Plastic Model Kit #35067
The Dingo was a British light two-man armoured car, relatively low and wide enough to have the required stability for fast off-road rides. Its initial armour was thin, just enough to stand against infantry ordnance. At the Army’s request, it was thickened, reaching 30mm (1.18 in) on the front nose and glacis. Deflecting armoured sloped panels were welded all around the central framework. The front driving compartment had four opening hatches. The engine was the regular Daimler 6-cyl 2.5 l 55 hp (41 kW), fed by a 300 l (79.25 gal) gasoline reserve (two tanks), which gave an incredibly long range for its small size. The transmission consisted of a pre-selector gearbox, fluid flywheel, five forward gears and five reverse gears, allowing steering with all four wheels. This feature gave the Dingo a very tight turning radius, only 7m (23 ft), but the system was tricky to master for inexperienced drivers, so a more conventional design with front-wheel steering was chosen.
During the course of wartime production, it appeared that the flat bottom plate, which allowed the crossing of uneven ground, was highly vulnerable to mines. The rubber tires were of the run-flat semi-solid type, so no spares were carried, but their toughness was compensated by the massive vertical coil springs, to give a smooth ride. There was a swiveling seat next to the driver, for a machine-gun servant/radio operator, equipped with a N°19 wireless radio set. The base armament was a removable cal. 0.303 (7.7 mm) Bren gun, with a dozen spare magazines. This armament could be swapped over for a heavier Boys antitank rifle (cal 0.55 in/14 mm). This gave the vehicle, which was fast and well-protected, with a good engine and low profile, a real advantage against all sorts of light vehicles, making it perfectly suited for reconnaissance and liaison missions.
The Dingo was produced from 1939 to 1945, and remained virtually unaltered. The Mark IB was the third variant of the series. It had a reverse cooling air flow and new armoured grilles for the radiator, allowing better ventilation. The bulk of these vehicles served in the Libyan desert.
This kit represents a British Dingo MK IB armoured car and three British crew-members: a driver, an observer and an officer. All three figures are dressed in British desert uniforms and armed with holstered revolvers. The officer has a pair of binoculars, a water bottle and a map case.
The kit contains 218 parts.
Includes parts for one armoured car and three figures.
Box: 345mm x 240mm x 60mm
Decals options:
- British Army, 7 Armoured Division, 1 Field Squadron Royal Engineers F 47483, World War II, Libya 1942, Sand with dark-earth stripes
- Canadian Army, 1 Canadian Army Tank Brigade, Calgary Reg Hunter, Operation Jubilee, Diepe, August 1942, Dark green, dark earth, black
- British Army, 7 Armoured Division, 4 Armoured Brigade, 5 Battalion F19370, World War II, Libya 1942, Sand
You can download instruction sheets here.
Miniart 1:35 Dingo Mk II Pz. Kpfw. Mk I 202 (e) w/Crew
£32.00 GBP
Miniart 1:35 - Dingo Mk II Pz. Kpfw. Mk I 202 (e) w/Crew - Plastic Model Kit #35074
The Dingo was a small two-man armoured car, relatively low and wide enough to have the required stability for fast off-road rides. Its initial armour was thin, just enough to stand against infantry ordnance. At the Army’s request, it was thickened, reaching 30mm (1.18 in) on the front nose and glacis. Deflecting armoured sloped panels were welded all around the central framework. The front driving compartment had four opening hatches. The engine was the regular Daimler 6-cyl 2.5 l 55 hp (41 kW), fed by a 300 l (79.25 gal) gasoline reserve (two tanks), which gave an incredible long range for its small size. The transmission consisted of a pre-selector gearbox, fluid flywheel, five forward gears and five reverse gears, allowing steering with all four wheels. This feature gave the Dingo a very tight turning radius, only 7m (23 ft), but the system was tricky to master for inexperienced drivers, so a more conventional design with front-wheel steering was chosen for the Mk.II.
During the course of wartime production, it appeared that the flat bottom plate, which allowed the crossing of uneven ground, was highly vulnerable to mines. The rubber tires were of the run-flat semi-solid type, so no spares were carried, but their toughness was compensated by the massive vertical coil springs, to give a smooth ride. There was a swiveling seat next to the driver, for a machine-gun servant/radio operator, equipped with a N°19 wireless radio set. The base armament was a removable cal. 0.303 (7.7 mm) Bren gun, with a dozen spare magazines. This armament could be swapped over for a heavier Boys antitank rifle (cal 0.55 in/14 mm). This gave the vehicle, which was fast and well-protected, with a good engine and low profile, a real advantage against all sorts of light vehicles, making it perfectly suited for reconnaissance and liaison missions.
The Dingo was produced from 1939 to 1945, and remained virtually unaltered.
The Mark I had a flexible sliding roof and the all-wheel steering. It was difficult to handle for inexperienced drivers.
The Mark IA was a sub-variant equipped with a folding roof.
The Mark IB had a reverse cooling air flow and new armored grilles for the radiator, allowing better ventilation. The bulk of these vehicles served in the Libyan desert.
The Mark II had a revised steering system, using only the front wheels. The lighting equipment was modernised, altogether with the Mark IB modification range.
The Mark III was the final version, coming in 1944 with a waterproof ignition system and no roof at all.
The kit contains 262 parts.
Includes parts for one armoured car and two figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Diorama w/Ruined Buildings
Sold Out
Miniart 1:35 - Diorama w/Ruined Buildings - Plastic model kit #36036
This kits contains 97 parts.
Model Dimension: Length 223mm, Width 173mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 European Street Diorama
Sold Out
Miniart 1:35 - European Street Diorama - Plastic model kit #36011
The kit contains 138 parts.
Model Dimension: Length 300mm, Width 215mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 European Tiled Roof
Sold Out
Miniart 1:35 - European Tiled Roof - Plastic model kit #35555
The kit contains 63 parts.
Model Dimension: Length 250mm, Width 252mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 Factory Corner w/steps
Sold Out
Miniart 1:35 - Factory Corner w/steps - Plastic model kit #35544
The kit contains 190 parts.
Model Dimension: Length 240mm, Height 265mm, Width 180mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 French Cafe
Sold Out
Miniart 1:35 - French Cafe - Plastic model kit #35513
The kit contains 125 parts.
Model Dimension: Length 147mm, Height 205mm, Width 95mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 French Tank Crew
£11.00 GBP
Miniart 1:35 - French Tank Crew - Plastic Figure Model Kit #35105
The kit contains 45 parts.
Includes parts for five figures.
Box: 260mm x 162mm x 35mm
Miniart 1:35 French Village House
Sold Out
Miniart 1:35 - French Village House - Plastic model kit #35510
The kit contains 158 parts.
Includes commercial posters.
Model Dimension: Length 250mm, Height 200mm, Width 180mm
Box: 345mm x 240mm x 90mm
Miniart 1:35 German Armoured Car Crew WWII
£10.00 GBP
Miniart 1:35 - German Armoured Car Crew WWII - Plastic Figure Model Kit #35072
The kit contains 49 parts for the assembly of five figures.
Box: 260mm x 162mm x 35mm
Miniart 1:35 German Artillery Tractor T-70 & 7.62cm Gun FK288 w/Crew
£43.00 GBP
Miniart 1:35 - German Artillery Tractor T-70 & 7.62cm Gun FK288 w/Crew - Plastic model kit #35039
Using captured or foreign produced equipment was a standard practise of the German Army since before the war, and the T-70 was no exception. The German designation for the T-70 was " Pz. Kpfw. T-70 743(r) " and was used mainly for reconnaissance and 'Internal Police Duties'. Some T-70's were used as ammunition, supply, or artillery tractors.
Ex-soviet 7.62cm FK288(r) (ZIS-3) guns were used by the 2., 3., 4., and 6. Batteries of the 16. Luftwaffenfelddivision (air force field division).
The kit contains 584 parts.
Includes parts for artillery tractor, limber, gun, five figures, and 42 photoetched parts.
Paints Required:
VAL950 - Black
VAL815 - Skintone
VAL920 - Grey Green
VAL894 - Field Green
VAL846 - Rust
VAL863 - Gun Metal
VAL825 - Brown
VAL998 - Bronze
VAL864 - Steel
VAL999 - Copper
VAL913 - Wood
VAL975 - Dark Green
Miniart 1:35 German City Building
Sold Out
Miniart 1:35 - German City Building - Plastic model kit #35506
The kit contains 143 parts.
Model Dimension: Length 200mm, Height 256mm, Width 105mm
Box: 345mm x 240mm x 70mm
Miniart 1:35 German Field Gun FK39 (r) 7.62cm
Sold Out
Miniart 1:35 - German Field Gun FK39 (r) 7.62cm - Plastic model kit #35104
The German FK39 (r) was formerly a Russian piece, designed to replace the aging 76mm M1902/30 series and formally adopted by the Red Army in 1939. The initial production covered the bare requirements of the Red Army, but when the Operation Barbarossa started Soviet factories had to begin production in much greater numbers. Those Soviet guns that fell into German hands were turned against their former owner and were designated the 7.62cm FK39(r). The Germans modified the gun to use Pak 36 (r) ammunition.
Includes parts for one gun, four ammo boxes with shells, and photo etched parts.
Box: 290mm x 190mm x 45mm
Miniart 1:35 German Grenades & Mines Set
Sold Out
Miniart 1:35 - German Grenades & Mines Set - Plastic Model Kit #35258
This kit includes German grenades and mines with ammo boxes and Molotov cocktails in a wooden box.
The kit contains 125 parts:
- 113 plastic parts
- 40 clear parts
- 12 PE parts
Decal sheet included.
Box: 260mm x 162mm x 35mm
Miniart 1:35 German Infantry Weapons and Equipment
£13.75 GBP
Miniart 1:35 - German Infantry Weapons and Equipment - Plastic Model Kit #35247
This kit includes parts for German infantry weapons and equipment.
Contents:
Arms: Walther G41 Semi-automatic rifle, Rifle 98k, Kar 98k Sniper Rifle w/Zf4 Scope, Selective-fire Automatic Rifle FG 42, MP 44 Assault Rifle, Submachinegun ERMA (EMP), Bergmann MP 34, Maschinenpistole MP 28, Maschinenpistole MP 40, Browning HP 35, Astra 600/43, Walther P 38, Luger P 08, Flare Pistol, Bayonet and Scabbard, Bayonet
Accessories: Binoculars, Case for binoculars, Browning holster, Astra holster, Walther holster, Walther holster opened, Luger holster, Flare pistol pigskin case, Flare pistol holster, Canteen and cup, Bread pouch (bag), Gas mask container, Map case, Cooking pot model 31, Cartridge belt, Cartridge belt Model 33 for Kar 98k, Cartridge belt for FG 42, Magazine pouches for MP 44, Cartridge belt for ERMA, Cartridge belt for MP 34, Cartridge belt for MP 28, Cartridge belt for MP 40, First-aid kit, Foldable spade, Shovel (Entrenching tool)
Other: 1/35 scale German maps, 1/35 scale German magazines
Kit details:
- 179 parts
- 114 plastic parts
- 65 photo-etched parts
- Decals included
- Box: 260mm x 162mm x 35mm
Download instructions with a full list of content here
Miniart 1:35 German Jagdpanzer SU-76(r) w/Crew
Sold Out
Miniart 1:35 - German Jagdpanzer SU-76(r) w/Crew - Plastic model kit #35053
It was common for the German army to use captured vehicles in battle. The SU-76 was a Soviet self-propelled gun used during and after World War II. Its German designation was Jagdpanzer SU-76. The SU-76 was based on a lengthened and widened version of the T-70 light tank chassis. Its simple construction made it the second most produced Soviet armoured vehicle of World War II, after the T-34 tank.
The SU-76M virtually replaced infantry tanks in the close support role. Its thin armour and open top made it vulnerable to antitank weapons, grenades, and small arms. Its light weight and low ground pressure gave it good mobility.
The kit contains 588 parts.
Includes parts for one tank and five figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 German Machine Gun Set
Sold Out
Miniart 1:35 - German Machine Gun Set - Plastic model kit #35250
This kit contains parts for building two MG-34 machine guns with bi-pods, two MG-42 machine guns with bi-pods and one German ZB-53 machine gun on a tripod. Several types of ammunition boxes and drums are included as well as a case for an additional MG-42 barrel.
The kit contains 84 parts and 38 photo-etched parts.Includes parts for the assembly of two MG-34, two MG-42 and one ZB-53 machine guns as well as accessories.
Box: 260mm x 162mm x 35mm
Miniart 1:35 German Pz. Kpfw T-70 743 (r) w/Crew
Sold Out
Miniart 1:35 - German Pz. Kpfw T-70 743 (r) w/Crew - Plastic model kit #35026
Using captured or foreign produced equipment was a standard practise of the German Army since before the war, and the T-70 was no exception. The German designation for the T-70M was " Pz. Kpfw. T-70 743(r) " and was used mainly for reconnaissance and 'Internal Police Duties'. Some T-70's had their turrets removed, and were used to tow Artillery.
The kit contains 348 parts.
Includes parts for one vehicle and five figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 German Staff Car 170V
£35.00 GBP
Miniart 1:35 - German Staff Car, Mercedes-Benz 170V - Plastic Model Kit #35103
The Mercedes-Benz W136 was Mercedes-Benz's line of inline-four cylinder automobiles from the mid-1930s into the 1950s. The model 170V made its public debut in February 1936. Between 1936 and 1939 it was Mercedes' top selling model. Between 1936 and 1942 over 75,000 were built.
The "V" in the 170 V's was an abbreviation of "Vorn" (front), added to differentiate it from the contemporary rear-engined Mercedes-Benz 170H (W28) ("H" for "Heck", rear) which used the same four cylinder 1697cc engine, but positioned at the back of the car.
Most of the cars produced were two or four door "Limousine" (saloon/sedan bodied cars), but the range of different body types offered in the 1930s for the 170V was unusually broad. A four-door "Cabrio-Limousine" combined the four doors of the four door "Limousine" with a full length foldaway canvas roof.
There was a two door two seater "Cabriolet A" and a two door four seater "Cabriolet B" both with luggage storage behind the seats and beneath the storage location of the hood when folded (but without any external lid for accessing the luggage from outside the car). A common feature of the 170V bodies was external storage of the spare wheel on the car's rear panel.
The kit contains 269 parts.
Includes parts for one German car.
Box: 345mm x 240mm x 60mm
Miniart 1:35 German Tank Crew - Afrika Korps
Sold Out
Miniart 1:35 - German Tank Crew, Afrika Korps - Plastic Figure Model Kit #35141
The German Afrika Korps (Deutsches Afrikakorps) was formed in 1941 with the purpose of assisting Italy in defending its African colonies. The Afrika Korps fought in Africa from 1941 until May 1943 when it surrendered along with other remaining Axis forces in North Africa.
This kit contains parts for the assembly of five German tank crew members. All figures are shirtless and wear tropical DAK shorts. Three of them have a tropical pith helmet on, and the other two - the early war type field side cap.
The kit contains 35 parts.
Box: 260 x 162 x 35 mm
Miniart 1:35 German Tank Crew At Rest
£11.00 GBP
Miniart 1:35 - German Tank Crew At Rest - Plastic Figure Model Kit #35198
The kit contains 58 parts.
Box: 260 x 162 x 35mm
Includes parts for five figures and a pig. Paint and glue are not included.
Miniart 1:35 German tank crew at work
Sold Out
Miniart 1:35 - German tank crew at work - Plastic Figure Model Kit #35010
A typical German tank crew consisted of a commander, a tank driver, gunners and loaders depending on the series of the tank. The total number of crew members also varied from one tank model to another.
The kit contains 40 parts.
Includes parts for five figures.
Box: 260mm x 162mm x 35mm
Miniart 1:35 German Tank Crew Winter, Special Edition
£14.00 GBP
Miniart 1:35 - German Tank Crew Winter, Special Edition - Plastic Figure Model Kit #35249
This kit contains parts for the assembly of five WWII German tank crew members in winter uniforms. Weapons and accessories are provided.
View instructions and full contents of this kit here
The kit contains 80 parts.
Box: 260mm x 162mm x 35mm
Miniart 1:35 German tank repair crew Special Edition
Sold Out
Miniart 1:35 - German tank repair crew Special Edition - Plastic Figure Model Kit #35319
The kit contains 36 parts.
Includes parts for five figures and work tools.
Box: 260mm x 162mm x 35m
Miniart 1:35 Italy 1943 Diorama
Sold Out
Miniart 1:35 - Italy 1943 Diorama - Plastic model kit #36008
Allied operations in and around Italy, from 1943 to the end of the war in Europe, are known as the Italian Campaign. Joint Allied Force Headquarters (AFHQ) was operationally responsible for all Allied land forces in the Mediterranean theatre, and it planned and commanded the invasion of Sicily in July 1943, followed shortly thereafter in September by the invasion of the Italian mainland and the campaign on Italian soil until the surrender of the German Armed Forces in Italy in May 1945. It is estimated that between September 1943 and April 1945, some 60,000-70,000 Allied and 150,000 German soldiers died in Italy. Overall Allied casualties during the campaign totaled about 320,000 and the corresponding German figure (excluding those involved in the final surrender) was well over 600,000.
The kit contains 81 parts.
Model Dimension: Length 247mm, Width 172mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 Leichter Pz.Kpfw. 202(e) with Crew Dingo Mk.I
£32.00 GBP
Miniart 1:35 - Leichter Pz.Kpfw. 202(e) with Crew Dingo Mk.I (Afrika Korps) - Plastic model kit #35082
The Daimler Mk. I, or the 'Dingo', was a British four wheel drive scout car often captured by the Nazis during WWII and renamed Leichter Pz.Kpfw. Mk. I 202(e).
Designed by Birmingham Small Arms Company, the Dingo was produced by Daimler in 1939. It had two man crew and was used as a reconnaissance vehicle. Its key advantages included the special gearbox, which allowed five speeds in both directions, and a four-wheel steering system, which gave a turning circle of 7 m. The Dingo first saw action with British troops in the Battle of France. It remained in British service till 1952 with over 6,000 units produced by that time.
The kit contains 204 parts.
Includes parts for the assembly of one armoured car and three figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Lithuanian City Building
Sold Out
Miniart 1:35 - Lithuanian City Building - Plastic model kit #35504
The kit contains 242 parts.
Includes German and Soviet posters.
Model Dimension: Length 280mm, Height 285mm, Width 130mm
Box: 345mm x 240mm x 80mm
Miniart 1:35 Panzerfaust 30/60 Set
£17.00 GBP
Miniart 1:35 - Panzerfaust 30/60 Set - Plastic Model Kit #35253
The Panzerfaust was a single shot German anti-tank weapon used from 1943 until the end of WWII. The Panzerfaust 30 weighed over 5 kg and had a total length of 1.045 metres. The warhead contained 0.8 kg of the mixture of TNT (trinitrotoluene) and hexogen explosives in the proportion of 1:1. The warhead was fitted on the launch tube that contained black powder propellant. The tube was discarded after firing which made the Panzerfaust the first disposable anti-tank weapon. The Panzerfaust 60 weighed 6.8 kg and its projectile speed was 45 m/s compared to 30 m/s of the Panzerfaust 30. Effective range of the Panzerfaust 60 was also increased from 30 to 60 m compared to that of the Panzerfaust 30.
This kit includes:
- 16 x Panzerfaust 30 with 4 boxes
- 16 x Panzerfaust 60 with 4 boxes
- Photo-etched parts
- Decals
The kit contains 192 parts.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Panzerschreck RPzB.54 & Ofenrohr RPzB.43 Set
Sold Out
Miniart 1:35 - Panzerschreck RPzB.54 & Ofenrohr RPzB.43 Set - Plastic Model Kit #35263
The Panzerschreck (tank's bane) was the common name for the Raketenpanzerbüchse (abbreviated to RPzB), an 88 mm calibre reusable anti-tank rocket launcher developed by Nazi Germany in World War II. Another popular nickname was Ofenrohr ("stove pipe").
The Panzerschreck was designed as a lightweight man portable anti-tank weapon and was largely a replica of the US military bazooka. The weapon was shoulder-launched and fired a fin-stabilized rocket with a shaped-charge warhead. It was made in smaller numbers than the Panzerfaust, which was a disposable recoilless gun firing an anti-tank warhead.
Download instructions here.
This kit includes:
- Panzerschreck RPzB.54
- Ofenrohr RPzB.43
- Ammo boxes, backpacks and projectiles
- Photo-etched parts
- Decals
Box: 260mm x 162mm x 35mm
Miniart 1:35 Personenwagen Typ 170V Saloon (Special Edition)
£35.00 GBP
Miniart 1:35 - Personenwagen Typ 170V Saloon (Special Edition) - Plastic model kit #35203
The Mercedes-Benz W136 was Mercedes-Benz's line of inline-four cylinder automobiles from the mid-1930s into the 1950s. The model 170V made its public debut in February 1936. Between 1936 and 1939 it was Mercedes' top selling model. Between 1936 and 1942 over 75,000 were built. Most of the cars produced were two or four door "Limousine" (saloon/sedan bodied cars).
The "V" in the 170 V's was an abbreviation of "Vorn" (front), added to differentiate it from the contemporary rear-engined Mercedes-Benz 170H (W28) ("H" for "Heck", rear) which used the same four cylinder 1697cc engine, but positioned at the back of the car.
The kit contains 267 parts.
Includes parts for the assembly of one vehicle and one figure.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Ruined Garage
Sold Out
Miniart 1:35 - Ruined Garage - Plastic model kit #35511
The kit contains 75 parts.
Model Dimension: Length 265mm, Height 180mm, Width 184mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 Scout Car Dingo Mk IA w/Crew
£32.00 GBP
Miniart 1:35 - Scout Car Dingo Mk IA w/Crew - Plastic Model Kit #35087
The Dingo was a British light two-man armoured car, relatively low and wide enough to have the required stability for fast off-road rides. Its initial armour was thin, just enough to stand against infantry ordnance. At the Army’s request, it was thickened, reaching 30mm (1.18 in) on the front nose and glacis. Deflecting armoured sloped panels were welded all around the central framework. The front driving compartment had four opening hatches. The engine was the regular Daimler 6-cyl 2.5 l 55 hp (41 kW), fed by a 300 l (79.25 gal) gasoline reserve (two tanks), which gave an incredible long range for its small size. The transmission consisted of a pre-selector gearbox, fluid flywheel, five forward gears and five reverse gears, allowing steering with all four wheels. This feature gave the Dingo a very tight turning radius, only 7m (23 ft), but the system was tricky to master for inexperienced drivers, so a more conventional design with front-wheel steering was chosen for the Mk.II.
During the course of wartime production, it appeared that the flat bottom plate, which allowed the crossing of uneven ground, was highly vulnerable to mines. The rubber tires were of the run-flat semi-solid type, so no spares were carried, but their toughness was compensated by the massive vertical coil springs, to give a smooth ride. There was a swiveling seat next to the driver, for a machine-gun servant/radio operator, equipped with a N°19 wireless radio set. The base armament was a removable cal. 0.303 (7.7 mm) Bren gun, with a dozen spare magazines. This armament could be swapped over for a heavier Boys antitank rifle (cal 0.55 in/14 mm). This gave the vehicle, which was fast and well-protected, with a good engine and low profile, a real advantage against all sorts of light vehicles, making it perfectly suited for reconnaissance and liaison missions.
The Dingo was produced from 1939 to 1945, and remained virtually unaltered.
The Mark I had a flexible sliding roof and the all-wheel steering. It was difficult to handle for inexperienced drivers.
The Mark IA was a sub-variant equipped with a folding roof.
The Mark IB had a reverse cooling air flow and new armored grilles for the radiator, allowing better ventilation. The bulk of these vehicles served in the Libyan desert.
The Mark II had a revised steering system, using only the front wheels. The lighting equipment was modernised, altogether with the Mark IB modification range.
The Mark III was the final version, coming in 1944 with a waterproof ignition system and no roof at all.
The kit contains 303 parts.
Includes parts for one armoured car and two figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Sevastopol Diorama
Sold Out
Miniart 1:35 - Sevastopol Diorama - Plastic model kit #36005
The kit contains 131 parts. Includes parts for diorama base, ruined building and 5 figures.
Model Dimension: Length 205mm, Width 135mm
Box: 345mm x 240mm x 60mm
Miniart 1:35 Soviet 100mm Shells w/Ammo Boxes
Sold Out
Miniart 1:35 - Soviet 100mm Shells w/Ammo Boxes - Plastic Model Kit #35088
The kit contains 108 parts.
Includes parts for six ammo boxes.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet 122mm Ammunition
Sold Out
Miniart 1:35 - Soviet 122mm Ammunition - Plastic Model Kit #35068
The kit contains 120 parts.
Includes parts for six ammo boxes.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet 45mm Shells w/Ammo Boxes
Sold Out
Miniart 1:35 - Soviet 45mm Shells w/Ammo Boxes - Plastic Model Kit #35073
The kit contains 156 parts.
Includes parts for six ammo boxes.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet Artillery Crew on Maneuvere
£20.00 GBP
Miniart 1:35 - Soviet Artillery Crew on Maneuvere - Plastic Figure Model Kit #35081
The Soviet anti-tank gun ZiS-3, also known as the 76-mm divisional gun M1942, was constructed at the Artillery Factory No. 92 in 1940 for the needs of the Red Army suffering enormous losses at the beginning of the Second World War. The gun was developed by V.G. Grabin, a Soviet artillery designer. The ZiS-3 design was based on the F-22USV cannon and the ZiS-2 anti-tank gun. Combining the F-22USV barrel and the ZiS-2 carriage, the ZiS-3 turned out to be far more effective compared to its prototypes. Unlike the F-22USV, the ZiS-3 was equipped with a muzzle brake which allowed to reduce recoil. Besides, its production was a lot easier and cheaper because most parts were manufactured by means of casting, and it was allowed to use materials lower in quality.
During the war, when fast production and large quantities were the highest priority, the ZiS-3 took part in combat without having been put to the tests. However, in the battlefield it proved its superiority over other anti-tank guns and later it was recognised by the authorities and obtained its official name - the divisional field gun model 1942. Due to its high combat effectiveness, the ZiS-3 had the largest share in the field gun production at wartime.
The kit contains 221 parts.
Includes parts for five figures and one anti-tank gun ZiS-3.
Box: 290mm x 190mm x 45mm
Miniart 1:35 Soviet Field Kitchen w/Horses
£32.00 GBP
Miniart 1:35 - Soviet Field Kitchen w/Horses - Plastic Figure Model Kit #35057
The kit contains 240 parts.
Includes parts for two horses, one field kitchen and one soldier.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Soviet GAZ-AA Cargo Truck
£34.00 GBP
Miniart 1:35 - Soviet GAZ-AA Cargo Truck - Plastic model kit #35124
A truck from Ford, Ford Model AA, was produced from 1927 till 1932. The vehicle was powered by a 3.3L I4 engine which produced a maximum of 40 horsepower at 2,200 rpm. It was designed to replace the T and TT models. The truck was available in a variety of body styles.
Ford licensed the production of the Model AA to several countries, including the Soviet Union. From 1932 to 1950 the USSR manufactured over 985,000 AA's, designated the GAZ AA. The cargo capacity of the Soviet model was 1,500 kg. Another version of this truck with a stronger 50HP engine is often called GAZ–MM, after the engine.
Includes parts for one cargo truck and two figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Soviet Gun ZIS-3 w/Horses
£38.00 GBP
Miniart 1:35 - Soviet Gun ZIS-3 w/Horses - Plastic model kit #35045
The ZiS-3 was a Soviet 76.2mm divisional field gun used during the Second World War. ZiS stood for "Zavod imeni Stalina" ("Factory named after Stalin"), the honorific title of Artillery Factory No. 92, which first constructed the gun.
When the ZiS-3 was first demonstrated to the Soviet authorities, Stalin called this gun "a masterpiece of artillery systems design". The Soviet Union produced over 103,000 ZiS-3 guns.
The kit contains 401 parts.
Includes parts for four horses, limber, gun and seven figures.
Box: 345mm x 240mm x 60mm
Miniart 1:35 Soviet infantry at rest
£8.00 GBP
Miniart 1:35 - Soviet infantry at rest - Plastic Figure Model Kit #35001
The kit contains 42 parts.
Includes parts for four figures.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet Infantry Weapons and Equipment Special Edition
£14.00 GBP
Miniart 1:35 - Soviet Infantry Weapons and Equipment Special Edition - Plastic Model Kit #35304
The kit contains 86 parts.
Includes parts for Soviet infantry weapons and equipment.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet Machine Guns and Equipment
Sold Out
Miniart 1:35 - Soviet Machine Guns and Equipment - Plastic model kit #35255
The set represents a selection of Soviet machine guns used before, during and after the Second World War as well as additional equipment and ammunition boxes.
Includes:
1 x DShK 12.7mm Heavy Machine gun
1 x 7.62mm Maxim 1910/30 Machine Gun (with two-wheeled trolley and photo-etch gun shield)
1 x 7.62mm Maxim 1940 Machine Gun (with two-wheeled trolley and photo-etch gun shield)
1 x 14.5mm PTRD-41 Anti-Tank Rifle
1 x 7.62mm DP Light Machine Gun
1 x 7.62mm DT Tank Machine Gun
2 x Maxim MG Ammo belts with cartridges
2 x Maxim MG Ammo belts without cartridges
2 x Maxim Ammo Boxes with open lip
4 x Maxim Ammo Boxes closed
3 x PTRD 14.5mm cartridges
4 x DP27 Magazine Boxes
1 x DP27 Canvas Pouch
4 x 7.62x54R Ammo Boxes
1 x Cartridge Bag
The kit contains 159 parts and a fret of photo-etched parts.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet Naval Troops (Special Edition)
£11.00 GBP
Miniart 1:35 - Soviet Naval Troops (Special Edition) - Plastic Figure Model Kit #35094
Building a Soviet fleet was a national priority, but many senior officers were killed in purges in the late 1930s. When Germany invaded in 1941 and captured millions of soldiers, many sailors and naval guns were detached to reinforce the Red Army; these reassigned naval forces had especially significant roles on land in the battles for Odessa, Sevastopol, Stalingrad, Novorossiysk, Tuapse, and Leningrad. The Baltic fleet was blockaded in Leningrad and Kronstadt by minefields, but the submarines escaped. The surface fleet fought with the anti-aircraft defence of the city and bombarded German positions.
Through Lend-Lease, the U.S. and Britain gave the USSR ships with a total displacement of 810,000 tons. The composition of the Soviet fleets in 1941 included 3 aged battleships, 7 cruisers, 59 destroyer-leaders and squadron-destroyers, 218 submarines, 269 torpedo boats, 22 patrol vessels, 88 minesweepers, 77 submarine-hunters, and a range of other smaller vessels.
During the war, many of the vessels on the slips in Leningrad and Nikolayev were destroyed (mainly by aircraft and mines), but the Soviet Navy received captured Romanian destroyers and Lend-Lease small craft from the U.S., as well as the old Royal Navy battleship HMS Royal Sovereign (renamed Arkhangelsk) and the United States Navy cruiser USS Milwaukee (renamed Murmansk) in exchange for the Soviet part of the captured Italian navy.
From the beginning of hostilities, Soviet Naval Aviation provided air support to naval and land operations involving the Soviet Navy. This service was responsible for the operation of shore-based floatplanes, long-range flying boats, catapult-launched and vessel-based planes, and land-based aircraft designated for naval use.
The kit contains 154 parts.
Includes parts for five figures, weapons and equipment.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet officers at field briefing Special Edition
£14.00 GBP
Miniart 1:35 - Soviet officers at field briefing - Plastic Figure Model Kit #35365
The kit contains 49 parts.
Includes parts for five Soviet officers.
Box: 260mm x 162mm x 35mm
Miniart 1:35 Soviet Soldiers at Rest (Special Edition)
Sold Out
Miniart 1:35 - Soviet Soldiers at Rest (Special Edition) - Plastic Figure Model Kit #35109
The kit contains 134 parts.
Includes parts for five figures, weapons and equipment.
Box: 260mm x 162mm x 35m
© 2025 Panzer Models. Prepared by Article.
